- Cocaine - Cocaine Vs Crack Cocaine | Bluelight.org
- Drug Info - - Crack Different Ways To Smoke It And Tricks ...
- How To Smoke Resin Out Of Crack Pipe - My Slim Fix
Drugs like crack cocaine, methamphetamines, DBT, PCP and cannabis are often times smoked in a glass pipes. Smoking out of a glass pipe is often times the preferred way to consume illegal drugs since it is more intense and more comfortable than snorting a substance through nasal passage ways.
- May 15, 2016 the easy way to smoke crack is with a glass, put paper foil over it and a condom to wrap it around the glass so the paper foil wont move, then make small needle holes on the north side and on the south a hole where u can inhale from, very easy and good luck.
- When you first hit it, you'll be holding the pipe upwards so as not to drop your hit - but as the crackling sound dies down and you begin to pull thick smoke, lower it down as you inhale. I like to hold it slightly downwards, so that it burns off the chore and doesn't run down past it into the pipe as much. Rotate the pipe as you inhale, also.
Bong Repair with Food Grade Silicone
Depending on where the break is you can use food grade silicone.
This method works on areas like your joints or the tube of your bong.
Food grade silicone works best when repairing cracks or notches in the glass; it's not going to help you if you have a completely broken bong that you need to piece back together.
Bong Repair Using Epoxy
Two component epoxy is a great long lasting way to fix your broken glass bong.
When buying epoxy, though, you need to make sure that you buy an epoxy with no solvents like a food grade epoxy.
Epoxy works best on fixing bongs with clean breaks, and the joints of the bong accessories found here.
If your bong has a real jagged break, you might consider buying a glass cutter to create a clean break, and then sand it down slightly before you applying epoxy to bond the two pieces of glass together.
If your break is at the base where bong water will be, after time the epoxy will get bogged down by water and start to leak.
You can help prevent this, by keeping your bong empty in between uses.
Fixing a Bong with Duct Tape
Now, this method is if you're are in a hurry, low on funds, or if you just want to get janky with it.
When buying epoxy, though, you need to make sure that you buy an epoxy with no solvents like a food grade epoxy.
Epoxy works best on fixing bongs with clean breaks, and the joints of the bong accessories found here.
If your bong has a real jagged break, you might consider buying a glass cutter to create a clean break, and then sand it down slightly before you applying epoxy to bond the two pieces of glass together.
If your break is at the base where bong water will be, after time the epoxy will get bogged down by water and start to leak.
You can help prevent this, by keeping your bong empty in between uses.
Fixing a Bong with Duct Tape
Now, this method is if you're are in a hurry, low on funds, or if you just want to get janky with it.
Duct tape works well when fixing small cracks or cheap glass bongs.
If your break is at the base where the water stays, then this fix will only work very temporarily at best.
Cocaine - Cocaine Vs Crack Cocaine | Bluelight.org
Fixing Your Bong with a Bucket
What? That's right, a bucket.
You can also use a sink, Tupperware bowl, or a bathtub. Pretty much anything that holds water.
This fix, well it's more of a workaround, is for when you break the base of your bong.
What you do is sit the bong in the water and voila, that's it.
The water in the bucket (or whatever you end up using) acts as the base of the bong and creates an airtight seal.
Hire a Pro
All right, cannabis adventurers, today's tip is a bit of a 'how-to'! If like many cannabis consumers you're using a custom-made glass pipe, you've likely noted that keeping that pipe looking as sparkly-clean, attractive—and functional—as the day you purchased it, is a wee bit harder than you may have expected.
The unctuous black resin that results from smoking cannabis is quite apt to stain clothing, your hands, and anything else it comes in contact with. Fortunately, maintenance of glass is hardly rocket science; it just takes patience, the right tools, and a little bit of advanced planning.
How to Clean Glass Pipe – Start Smart
What You'll Need to Clean Your Glass Cannabis Pipe
First of all, let's lay out the materials you'll want to have close at hand before cleaning:
- A bobby pin or other thin wire implement
- Paper towels, tissue or expendable rag
- Sealable plastic freezer baggie
- Salt, preferably coarse or kosher
- Isopropyl (rubbing) alcohol, 90% or higher
- Pipe cleaner (available at craft stores or well-stocked drug stores and dispensaries)
Drug Info - - Crack Different Ways To Smoke It And Tricks ...
How to Clean Glass Pipe In 4 Easy Steps:
Step 1: Soften the resin by applying heat. One of the easiest ways, naturally, is to use the pipe for its intended purpose, just so long as you feel that imbibing won't muddle the cleaning process!
Step 2: Using the bobby pin or similar device, gently scrape the resin from the bowl, walls, and mouthpiece of the pipe. Keep in mind that the resin will stain most anything it comes in contact with, so exercise caution and have a paper towel or similar in place to wipe off the collected resin. Of course, if you want to save the resin for smoking later, you can collect it all in a non-reactive glass or plastic vessel of some kind.
Step 3: Break out the freezer baggie! Place the pipe in the bag with a good scoop (we recommend a tablespoon or two) of salt, then enough rubbing alcohol to submerge the pipe completely. Sealing up the baggie, start gently swishing and rubbing with your fingers to scrub the pipe with the salt-and-alcohol mixture. Keep this up for a good minute or two (you may want to employ a timer if cannabis has altered your perception of time), then allow the pipe to sit in the liquid for a couple of hours. Repeat the gentle scrub if you feel it's needed.
Step 4: Once the scrub is complete, rinse the pipe thoroughly in hot water, gently dry with a towel of some sort, and inspect. At this point, you may want to use the pipe cleaner to remove any stubborn traces of resin and restore some of the pipe's original shine. If you haven't gone too long between cleanings, your pipe should be shiny and ready for further use!
How to Clean Glass Pipe Without Alcohol
Although we feel it's a safe household solvent when thoroughly rinsed, some people prefer to avoid isopropyl alcohol altogether.
How To Smoke Resin Out Of Crack Pipe - My Slim Fix
An alternative cleaning regimen is to boil enough tap water to cover the pipe by a few inches in a saucepan, reduce the heat to a simmer, and submerge the pipe for half an hour or so. Be sure that the simmer is low enough to release gentle bubbles, but not evaporate off and leave the pipe uncovered, which could crack it. After the time has elapsed, carefully drain the water and—exercising extreme caution as the pipe will be hot—clean and dry it thoroughly with a towel and/or pipe cleaner.
